AMERITRON AL-80B Spécifications télécharger pdf (Page 12)

98 http://www.ameritron.com

AL-811/AL-811H

Specifications:

Input:

Circuit type: Pi-network,

slug tuned coils.

Maximum VSWR at reso-

nance: 1.3:1

Minimum 2:1 VSWR

bandwidth: 15%. Max.

drive power permissable:

AL-811: 80 Watts; AL-

811H: 100 Watts. Typical

drive rated output: AL-

811: 60 Watts; AL-811H:

75 Watts

Output:

Typical SSB PEP voice

operation: AL-811: 600

Watts, AL-811H: 800

Watts.

Typical CW operation:

AL-811: 400 Watts; AL-

811H: 600 Watts. 1/2 hour

PEP two tone test:

AL-811: 500 Watts; AL-

811H: 650 Watts. 1/2 hour

continuous carrier

(RTTY): AL-811: 300

Watts input; AL-811H: 400

Watts input.

Power Supply:

Circuit type: full wave

bridge. No load voltage:

1700 Volts. Full load volt-

age: 1500 Volts. Full load

current: AL-811: 550 mA;

AL-811H: 650 mA.

Regulation: 10%.

Maximum draw at rated

output: AL-811: 8 A; AL-

811H: 10A. AC Input:

120 V, 50/60 Hz (AL-

811/H) 240 V, 50/60 Hz

(AL-811X/AL-811HX).

Tubes:

Type: (AL-811: 3)

(AL-811H: 4) 811A verti-

cally mounted.

Continuous dissipation:

65 Watts per tube. Warm-

up time:

5 seconds

Metering:

Multimeter: reads HV and

plate current. Grid Meter:

Reads PA grid current

ALC:

Negative going, 0-20 V,

adjustable, phono jack

*Efficiency SSB (envelope

crest): greater than 70%

MARS/WARC:

Yes, set to the nearest

band.

Connectors:

Relay: engages amplifier

when grounded. +12 VDC

open circuit and supplies

100 mA when grounded. A

built-in back-pulse can-

celling diode protects the

exciter.

RF input:

SO-239, 50 Ohm input.

RF Out:

50 Ohms with full power

into any SWR below 3:1.

Power:

NEMA 5-15P, 120 Volts.

Dimensions:

Dx13

Wx8

H inch-

es.

Operating Weight:

32 pounds.

Shipping Weight:

41 pounds.

Frequency Coverage:

Domestic model: 160, 80,

40, 30, 20, 17, 15 Meters.

10/12 Meters with modifi-

cation. Must present FCC

license at time of sale to

obtain modification details.

Third Order IMD at

Rated Output: -33 dB.

AL-80B

Specifications:

Input:

Circuit type: Pi-network,

slug tuned coils.

Maximum VSWR at reso-

nance: 1.3:1 or less.

Minimum 2:1 VSWR

bandwidth: 20% of center

frequency. Max. drive

power permissable: 100

Watts. Typical drive for

full power output: 85 W.

Output:

Typical SSB PEP voice

operation: 1000 Watts.

Typical CW operation:

800 Watts. 1/2 hour PEP

two tone test:

800 Watts. 1/2 hour con-

tinuous carrier (RTTY):

500 Watts.

Power Supply:

Circuit type: Full wave

voltage doubler. No load

voltage: 3000 Volts. Full

load voltage: 2700 Volts.

Full load current: .450

Amp. Regulation: 10%.

Transformer: 26 pounds.

Capacitors: 33 uFd total,

computer grade.

Maximum draw at rated

output: 12 Amps. AC

Input: 120 V, 50/60 Hz.

Tubes:

Type: Classic 3-500.

Continuous dissipation:

500 Watts. Warm-up

time: 5 seconds.

Metering:

Multimeter: reads HV,

forward power, reflected

power, SWR, ALC, ALC

set. Current Meter:

Reads plate and grid cur-

rent.

ALC:

True ALC 0-10V negative,

front panel adjustable.

Efficiency CW: Typically

66% or greater.

*Efficiency SSB (envelope

crest): Approximately 66%

or greater.

MARS/WARC:

Yes, set to the nearest

band.

Connectors:

Keying: Supplies 100 mA

when grounded, built-in

back-pulse cancelling

diode, protects the exciter.

12 VDC open circuit.

RF input:

SO-239, 50 Ohm input.

RF Out:

50 Ohms with full power

into any SWR below 3:1.

Power:

NEMA 5-15P, 120 Volts.

Dimensions:

Dx14

Wx8

H inch-

es.

Operating Weight:

48 pounds.

Shipping Weight:

Unit, 54 lbs.; Tube, 3 lbs.

Frequency Coverage:

Domestic model: 160, 80,

40, 30, 20, 17, 15 Meters.

10/12 Meters with modifi-

cation. Must present FCC

license at time of sale to

obtain modification details.

Third Order IMD at

Rated Output: -35 dB.

AL-572

Specifications:

Input:

Circuit type: Pi-network,

slug tuned coils.

Maximum VSWR at reso-

nance: 1.3:1 or less.

Minimum 2:1 VSWR

bandwidth: 20% of center

frequency. Max. drive

power permissable: 100

Watts.

Typical drive for full

power output: 70 Watts.

Output:

Typical SSB PEP voice

operation: 1300 Watts

nominal (7 MHz).

Typical CW operation:

900 Watts nominal.

1/2 hour PEP two tone

test: 1000 Watts.

1/2 hour continuous car-

rier (RTTY): 650 Watts.

Power Supply:

Circuit type: Full wave

voltage doubler. No load

voltage: 2800 Volts. Full

load voltage: 2500 Volts.

Full load current: .7 Amp.

Regulation: 14% or less.

Transformer: 21 pounds.

Capacitors: 33 mFd total,

computer grade.

Maximum draw at rated

output: 16 Amps. AC

Input: 120 V, 50/60 Hz.

Tubes: Type: 572B (x4).

Continuous dissipation:

640 Watts.

Warm-up time: 5 seconds.

Metering:

Multimeter: reads HV,

forward power, reflected

power, SWR, ALC, ALC

set. Current Meter:

Reads plate and grid cur-

rent.

ALC:

True ALC 0-10V negative,

front panel adjustable.

Efficiency CW: Typically

60% or greater.

*Efficiency SSB (envelope

crest): Typically 60% or

greater.

MARS/WARC:

Yes, set to the nearest

band.

Connectors:

Keying: Supplies 100 mA

when grounded, built-in

back-pulse cancelling

diode, protects the exciter.

12 VDC open circuit.

RF input:

SO-239, 50 Ohm input.

RF Out:

50 Ohms with full power

into any SWR below 3:1.

Power:

NEMA 5-15P, 120 Volts.

Dimensions:

Dx14

Wx8

H inch-

es.

Operating Weight:

40 pounds.

Shipping Weight:

48 lbs.

Frequency Coverage:

Domestic model: 160, 80,

40, 30, 20, 17, 15 Meters.

10/12 Meters with modifi-

cation. Must present FCC

license at time of sale to

obtain details.

Third Order IMD at

Rated Output: -34 dB

(below PEP rated output).

AL-800/AL-800H

Specifications:

Input:

Circuit type: Pi-network,

resistor attenuated/slug

tuned coils. Maximum

VSWR at resonance:

1.3:1 or less. Minimum

2:1 VSWR bandwidth:

within +20% or -40% of

selected band/ within 20%

of center frequency.

Max. drive power per-

missable: 100 Watts.

Typical drive for full

power output: 70/55Watts.

Output: Circuit type Pi/Pi-

network output.

Typical SSB PEP voice

operation: 1250/1500+W

Typical CW continuous

operation: 1000/1500 W.

1/2 hour PEP two tone

test: 1000/1500 Watts.

1/2 hour continuous car-

rier (RTTY): 750/1000 W.

Power Supply: Circuit

type: Full wave voltage

doubler. No load voltage:

2600 Volts. Full load volt-

age: 2300/2250 V. Full

load current: 1/1.2 A.

Regulation: 12%

less/15%.

Transformer: 32 lbs grain

oriented El lamination.

Capacitors: 78/63 uFd

total, high current comput-

er grade.

Maximum draw at rated

output:12/13A@240 VAC.

Typical line current at 1500

Watt PEP output. 9A at 240

VAC. Power line current in

standby: .5 A at 240 VAC.

AC Input: 120V, 50/60 Hz.

Tubes: Eimac

3CX800A7.

Continuous dissipation:

800W per tube, 1600W

total. Warm-up time: 180

seconds. Estimated life:

6,000-8,000 hours ICAS.

Metering: Multimeter:

reads Peak forward power,

Peak reflected power, SWR,

ALC threshold output volt-

age, and high voltage.

Current Meter: Reads

plate and grid current.

ALC: Negative going, 0-

10 V, phono jack output,

front panel adjustments.

Efficiency CW: Approx-

imately 65-66% or greater.

Eff. SSB (envelope crest):

Approx. 66% or greater.

MARS/WARC: Yes, set to

the nearest band.

Connectors:

Keying: Requires contact

closure or sink of +12

VDC at 100 mA, back

pulse protected, phono

jack.

RF input:

SO-239, 50 Ohm input.

RF Out:

50 Ohms with full power

into any SWR below 3:1.

Power: NEMA 5-15P,

120/240 Volts.

Dimensions:

Dx14

Wx8

H in.

Operating Weight: 51/52

lbs.

Shipping Weight: Unit,

59/60 lbs,; Tubes, 3/5 lbs.

Frequency Coverage:

Domestic model: 160, 80,

40, 30, 20, 17, 15 Meters.

10/12 Meters with modifi-

cation. Must present FCC

license.

Third Order IMD at

Rated Output: -35 dB.

AL-82

Specifications:

Input:

Circuit type: Pi-network,

slug tuned coils.

Maximum VSWR at reso-

nance: 1.2:1

Minimum 2:1 VSWR

bandwidth: 20%.

Max. drive power per-

missable: 130 Watts.

Typical drive rated out-

put: 100 Watts

Output:

Typical SSB PEP voice

operation: 1500 Watts.

Typical CW continuous

operation: 1500 Watts.

30 second PEP two tone

test:1800 Watts plus.

1/2 hour PEP two-tone

test: 1800 Watts.

Power Supply:

Circuit type: full wave

bridge, capacitor input.

No load voltage: 3600

Volts.

Full load voltage: 3300

Volts.

Full load current: .8 Amp.

Regulation: 10% or better.

Transformer: 32 lb

HypersilR, capacitors: 26

uFd total, computer grade.

Maximum draw at rated

output: 13 Amps.

AC Input: 240 V, 50/60

Hz.

Tubes:

Type: 3-500 Classic (2).

Continuous dissipation:

1000 Watts.

Warm-up time: 5 seconds.

Metering:

Multimeter: Plate current,

plate voltage, drive/ALC,

power output (PEP Watts).

Grid Meter: Reads PA

grid current

ALC:

Negative going, 0-20 V,

phono jack

Efficiency CW: 65% typi-

cal.

*Efficiency SSB (envelope

crest): 62% typical.

MARS/WARC:

Yes, set to the nearest

band.

Connectors:

Keying: engages amplifier

when grounded. +12 VDC

open circuit and supplies

100 mA when grounded. A

built-in back-pulse can-

celling diode protects the

exciter.

RF input:

SO-239, 50 Ohm input.

Power:

NEMA 6-15P, 240 Volts.

Dimensions:

Dx17Wx10H inches.

Operating Weight:

76 pounds.

Shipping Weight:

Unit, 50 lbs.; Tubes, 6 lbs.;

Transformer, 35 lbs.

Frequency Coverage:

Domestic model: 160, 80,

40, 30, 20, 17, 15 Meters.

10/12 Meters with modifi-

cation. Must present FCC

license at time of sale to

obtain modification details.

Third Order IMD at

Rated Output:

-34 dB at 1500 Watts

Output.

* Exact performance measurements may vary due to the

accuracy of test equipment and the measurement meth-

ods used. (Prices and specifications subject to change

without notice or obligation).

MFJCatP98_2012.qxd 4/11/2012 12:11 PM Page 1

1 2 ... 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

AMERITRON AL-80B Spécifications Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio AMERITRON AL-80B